RST Ecoenergy Pvt. Ltd.Innovating the Future
FREE ENGINEERING TOOLS / Lighting & power

Free Lighting & Battery Calculators

Estimate light quantity, beam coverage, battery Ah and DC cable voltage drop. Free online calculators with editable factors, visible formulas and examples.

LUMEN METHOD / INITIAL PLANNING

Estimate fixture quantity.

Use your required lux and fixture data. Utilisation and maintenance factors are editable assumptions, not a site-specific lighting design.

CIRCULAR CONE / FULL BEAM ANGLE

Estimate beam footprint.

Use the full included angle, not half-angle. The lux result assumes a uniform cone; actual searchlight intensity needs measured candela or photometric data.

ENERGY MODEL / EDITABLE ASSUMPTIONS

Build your load schedule.

LoadW / unitQtyh / day

Peak power assumes every listed load operates together. AC current is an illustrative sinusoidal-load estimate; motor starting and non-linear load behaviour are not modelled.

DC TWO-WIRE LOOP / NOMINAL RESISTIVITY

Check cable voltage drop.

Includes outgoing and return conductor length at nominal room-temperature resistivity. This is not a cable ampacity, temperature-rise or protection-sizing tool.

How this calculator works

Lighting uses the lumen method. Beam diameter = 2 × distance × tan(full beam angle / 2). Battery Ah = load Wh × margin / (bank voltage × usable discharge × efficiency).

Use your actual inputs

Material densities and operating factors are editable planning assumptions. Replace them with supplier data or measurements for the configuration you intend to use.

Keep calculations inspectable

Inputs, units and results are shown together. Save a CSV or print the calculation to share your planning assumptions.

Need help with an RST product or a custom configuration? Discuss your requirement ↗

Does a beam estimate replace photometric data?

No. The beam tool assumes uniform light within a circular cone. Real centre intensity and distribution require manufacturer candela data or an IES/LDT file. The lumen method does not model shadows, glare, uniformity or exact fixture spacing.

Why can measured battery runtime differ?

Battery age, temperature, discharge rate, BMS limits and inverter standby power affect usable energy. This energy model excludes Peukert behaviour and does not specify cable, protection or emergency-lighting compliance.

Technical context: battery capacity and discharge-rate effects.

FREE TOOL / PRACTICAL GUIDE

How to use the Lighting & Battery Calculators.

Use four free planning tools in one place: lighting quantity by the lumen method, circular beam footprint, load-and-battery capacity, and DC voltage drop. These estimates help you prepare requirements for portable lights, area lighting and battery-powered equipment.

  1. Select Lighting quantity, Beam coverage, Load & battery or DC voltage drop.
  2. Enter actual site dimensions, fixture data, load duration or cable details. Review editable efficiency and utilisation assumptions.
  3. Calculate and inspect the units and result. Download a CSV or print the estimate, then confirm final selection with relevant product and installation data.

Worked example

Lighting example: 20 m × 10 m at 200 lux, using 10,000-lumen fixtures with utilisation factor 0.6 and maintenance factor 0.8, needs 9 fixtures after rounding up. Battery example: a 200 W load for 5 hours at 24 V, 80% usable discharge, 90% efficiency and 1.15 margin needs approximately 66.55 Ah nominal capacity.

कितनी lights चाहिए, beam कितना फैलेगा और load के लिए कितनी battery Ah चाहिए—इनका प्रारंभिक अनुमान निकालें। Final selection वास्तविक product data और installation conditions पर निर्भर है।

Frequently asked questions

How is light quantity calculated?

Required fixtures = area × target lux ÷ (fixture lumens × utilisation factor × maintenance factor), rounded up. This does not model glare, uniformity or obstructions.

How do I calculate battery capacity in Ah?

The energy model divides required load energy in Wh, including the selected margin, by battery voltage, usable discharge fraction and efficiency. Temperature, ageing and discharge rate affect real runtime.

Does this replace a final lighting or electrical design?

No. Confirm photometric data, fixture ratings, battery behaviour, cable protection and installation requirements before purchase or installation. The DC drop tool is not an AC cable-sizing or safety certification tool.

ENGINEERED IN INDIAIndigenous development. Indian ambition.

Specialised lighting, electronics and engineering—supporting the spirit of Atmanirbhar Bharat.

RST ECOENERGY

Request a quotation

Open the quotation form as a full page ↗

RST CREDENTIALS & RESOURCES

Request document download

Open request as a full page ↗